Abstract This work focuses on characterizing the role of different triblock copolymers on the dispersion of nanoparticles in an epoxy matrix and in the thermal and mechanical properties of the resulting nanocomposites, using Poly (ethylene glycol) - block-poly (propylene glycol) - block-poly (ethylene glycol) (PEG-b-PPG- b-PEG) with 30% PEG, and poly (propylene glycol) - block-poly (ethylene glycol) - block-poly (propylene glycol) (PPG-b-PEG-b-PPG) with 50% PEG. The nanoparticles employed have different geometries: carbon nanotubes, graphene nanoplatelets and carbon black (spherical). Both copolymers were miscible in epoxy. The results suggest that the copolymers viscosity may be interfering with the dispersion of the nanoparticles in the matrix: the PPG-b- PEG-b-PPG50% copolymer has a higher viscosity than the PEG b-PPG-b-PEG30%, which facilitates their dispersion and an increase in mechanical properties. The PEG fraction was an important factor in the dispersion of nanoparticles in the epoxy matrix. The higher the PEG content in the copolymer block, the greater the synergy shown in the mechanical properties, since the nanoparticles inhibited the plasticizing effect of the block copolymer.

ABSTRACT >Injection molds can fail after a certain period of use, which may compromise the final part’s integrity and quality, but that can be solved using welding repair processes. This work aimed to investigate the influence of AISI P20 molds repaired by Gas Tungsten Arc Welding (GTAW) and Nd-YAG laser-welding processes on the properties of injection-molded parts with semi-crystalline (polypropylene) and amorphous (polycarbonate and acrylonitrile butadiene and styrene terpolymer) thermoplastics. Welds were prepared by machining 0.8 mm-deep 40 mm x 5 mm grooves to be filled by GTAW and Nd-YAG laser-welding deposits, in order to simulate the repair of AISI P20 molds. All polymers were injected into weld-repaired and unrepaired molds, and then evaluated in terms of microstructure, crystallinity degree, mechanical properties and gloss. The results suggest that the repaired region for both studied welding processes, despite the difference in hardness of the weld region, does not significantly affect the properties of semi-crystalline and amorphous injected polymers.

RESUMO Filmes de polietileno de alta densidade (PEAD) foram tratados por plasma radiofrequência (RF) de N2/O2. Foi investigado o efeito da pressão do gás de trabalho N2/O2, do plasma, na texturização superficial do filme. O plasma gerado em baixa potência (20W) permite manter a amostra em baixa temperatura (T<40°C) durante o tratamento de superfície. Os resultados mostram que a rugosidade superficial, em escala nanométrica, é muito sensível à pressão do gás de trabalho, entre 0,01Torr e 0,5Torr. Quando o material é tratado em pressão mais baixa (0,01Torr), observa-se a formação de uma estrutura superficial nanométrica de vales e picos com elevada regularidade. Por outro lado, quando o tratamento é feito em pressão mais alta (0,5 Torr), observa-se a formação de uma textura mais grossa na superfície da amostra, além da formação de ilhas de moléculas oxidadas. Em todos as condições estudadas, as amostras tornaram-se hidrofílicas após o tratamento por plasma, mantendo a característica de hidrofilicidade durante vários dias após o tratamento, retornando gradativamente à condição original de molhabilidade.

ABSTRACT HDPE films were treated in the post-discharge region of N2/O2 plasma, powered by a radio frequency power supply. Therefore, in this paper, it was investigated the role of pressure in molding the nano-topography of the polymer. The treatment was carried out in low temperature (T <40 ° C) and time of 5.0 min, in order to preserve the integrity of the polymer bulk. It is well known that the production and recombination rate of reactive species in the plasma depends on the working gas pressure. Results show that the surface nano-roughness is very sensitive to pressure, between 0.01Torr and 0.5Torr, making it possible to use as a fine control parameter for polymer nano-texturing. In the lower pressure treatment it was observed regular nano-peaks and nano-troughs on the surface of the sample. Contact angle measurements show that, in general, the surface becomes hydrophilic after N2/O2 plasma treatment. In addition, samples treated in higher pressure generate oxidized islands by the action of the oxidizing plasma. All samples became more hydrophilic after plasma treatment, maintaining this hydrophilicity characteristic for several days.

This work aims to investigate the role of epoxy addition in high density polyethylene (HDPE) matrix. The block copolymer polyethylene-b-poly (ethylene glycol) (PEG-co-PE) was used as a compatibilizer. The samples were obtained by melt mixing using a torque rheometer. Instrumental nanoindentation was used to determine Young's modulus and nanohardness, thermal properties were analyzed by differential scanning calorimetry (DSC) and phase morphology was investigated through transmission and scanning electronic microscopy. The epoxy addition increased HDPE crystallinity by 13% and Young's modulus by 8%. The addition of PEG-co-PE decreased the size of dispersed phase by approximately 50% and improved phase adhesion and homogeneity compared to the blends without block copolymer. The experimental results were compared to numerical results obtained from the use of the homogenization by asymptotic expansion approach. The numerical results presented a fair agreement to the experimental values.

ABSTRACT Objective: to evaluate the risk of infection and illness caused by Mycobacterium tuberculosis among health care and security staff in prisons in two regions of Rio Grande do Sul (RS). Method: cross-sectional study involving prison staff. An interview and sputum smear microscopy and culture were performed. Latent infection was evaluated according to the result of the tuberculin test (TT), self-referred. Results: among staff who had a TT, 10 (83.3%) in the central region and 2 (16.7%) in the southern region were considered reactors. Length of employment among prison officers who reacted to TT was 15.3 years, and among health care workers, 4.1 years (p = 0.01). No cases of active tuberculosis (TB) were identified. Conclusion: prevalence of latent TB was 27.9%. Length of employment between different professional categories and their working regions was considered a risk factor for latent TB.

RESUMEN Objetivo: evaluar el riesgo de infección y de la enfermedad por Mycobacterium tuberculosis entre los profesionales de la salud y seguridad en los centros penitenciarios en dos regiones del estado de Rio Grande do Sul (RS). Método: estudio transversal con la participación de profesionales de la prisión. Se llevó a cabo una entrevista, la baciloscopia y cultivo de esputo. La infección latente se evaluó de acuerdo con el resultado de la prueba de la tuberculina (TST) mediante auto-reporte. Resultados: entre los trabajadores que realizaron la TST en la región central, 10 (83,3%) fueron considerados reactores; y 2 (16,7%) en la región Sur. El tiempo de trabajo entre los agentes de la prisión con reacción a la TST fue de 15,3 años, y entre los trabajadores de la salud fue de 4,1 años (p = 0,01). No hubo casos identificados de la tuberculosis (TB) activa. Conclusión: la prevalencia de la TB latente fue del 27,9%. El tiempo de trabajo entre las diferentes categorías profesionales y la región en la que trabajan fueron considerados factores de riesgo para la TB latente.

RESUMO Objetivo: avaliar o risco de infecção e adoecimento por Mycobacterium tuberculosis entre profissionais de saúde e de segurança em casas penitenciárias de duas regiões do Rio Grande do Sul (RS). Método: estudo transversal, envolvendo profissionais de penitenciárias. Foi realizada uma entrevista, baciloscopia e cultura de escarro. A infecção latente foi avaliada de acordo com o resultado do teste tuberculínico (TT), auto-referido. Resultados: entre os trabalhadores que realizaram o TT na região central, 10 (83,3%) foram considerados reatores; e na região sul, 2 (16,7%). O tempo de trabalho entre os agentes penitenciários reatores ao TT foi 15,3 anos e entre os trabalhadores da saúde 4,1 anos (p = 0,01). Não foram identificados casos de Tuberculose (TB) ativa. Conclusão: a prevalência de TB latente foi 27,9%. O tempo de trabalho entre as diferentes categorias profissionais e a região em que trabalham foram considerados fator de risco para TB latente.

RESUMO Objetivo: avaliar o risco de infecção e adoecimento por Mycobacterium tuberculosis entre profissionais de saúde e de segurança em casas penitenciárias de duas regiões do Rio Grande do Sul (RS). Método: estudo transversal, envolvendo profissionais de penitenciárias. Foi realizada uma entrevista, baciloscopia e cultura de escarro. A infecção latente foi avaliada de acordo com o resultado do teste tuberculínico (TT), auto-referido. Resultados: entre os trabalhadores que realizaram o TT na região central, 10 (83,3%) foram considerados reatores; e na região sul, 2 (16,7%). O tempo de trabalho entre os agentes penitenciários reatores ao TT foi 15,3 anos e entre os trabalhadores da saúde 4,1 anos (p = 0,01). Não foram identificados casos de Tuberculose (TB) ativa. Conclusão: a prevalência de TB latente foi 27,9%. O tempo de trabalho entre as diferentes categorias profissionais e a região em que trabalham foram considerados fator de risco para TB latente.

ABSTRACT Objective: to evaluate the risk of infection and illness caused by Mycobacterium tuberculosis among health care and security staff in prisons in two regions of Rio Grande do Sul (RS). Method: cross-sectional study involving prison staff. An interview and sputum smear microscopy and culture were performed. Latent infection was evaluated according to the result of the tuberculin test (TT), self-referred. Results: among staff who had a TT, 10 (83.3%) in the central region and 2 (16.7%) in the southern region were considered reactors. Length of employment among prison officers who reacted to TT was 15.3 years, and among health care workers, 4.1 years (p = 0.01). No cases of active tuberculosis (TB) were identified. Conclusion: prevalence of latent TB was 27.9%. Length of employment between different professional categories and their working regions was considered a risk factor for latent TB.

RESUMEN Objetivo: evaluar el riesgo de infección y de la enfermedad por Mycobacterium tuberculosis entre los profesionales de la salud y seguridad en los centros penitenciarios en dos regiones del estado de Rio Grande do Sul (RS). Método: estudio transversal con la participación de profesionales de la prisión. Se llevó a cabo una entrevista, la baciloscopia y cultivo de esputo. La infección latente se evaluó de acuerdo con el resultado de la prueba de la tuberculina (TST) mediante auto-reporte. Resultados: entre los trabajadores que realizaron la TST en la región central, 10 (83,3%) fueron considerados reactores; y 2 (16,7%) en la región Sur. El tiempo de trabajo entre los agentes de la prisión con reacción a la TST fue de 15,3 años, y entre los trabajadores de la salud fue de 4,1 años (p = 0,01). No hubo casos identificados de la tuberculosis (TB) activa. Conclusión: la prevalencia de la TB latente fue del 27,9%. El tiempo de trabajo entre las diferentes categorías profesionales y la región en la que trabajan fueron considerados factores de riesgo para la TB latente.

ABSTRACT Conducting polymers presents many potential applications such as biosensors and biofuelcells. However, to be used in those devices, a thin film must be deposited onto a conducting and biocompatible substrate. In this work, carbon nanotubes (CNT) were mixed in a poly (lactic acid) - PLA - matrix with different compositions (from 0.25 to 5.0 %) in order to form conducting composites suitable to the deposition of a conducting polymer. Thermal properties of PLA/CNT composites were evaluated by Thermogravimetry (TG) and Differenctial Scanning Calorimetry (DSC), and the electrical properties were evaluated by 2-probe method and by Electrochemical Impedance Spectroscopy (EIS). Thermal analysis showed and influence of CNT quantities on PLA crystallization, which also showed an influence on conductivity of the tested materials. Besides, the conductivity of PLA/NTC 1% film showed similar values of the conducting polymer (Pani) itself.

ABSTRACT In this paper, nanocomposites with multiwalled carbon nanotubes (MWCNT) or graphene nanosheets were prepared using a high density polyethylene (HDPE) matrix. Two different processes were employed: a solution method and a melt mixing method. The crystallinity index of the HDPE showed similar levels in nanocomposites after the addition of carbon nanotubes. It can be seen that the preparation process modified the degree of crystallinity of the HDPE matrix with graphene nanosheets. Nanocomposites prepared by the solution method showed a decrease in the crystallinity index. The addition of carbon nanotubes led to an increase of Young's Modulus with an increase in the MWCNT quantity, regardless of the preparation process used, with a 22.8 % increase for composites with 0.5 wt% of CNTs. The nanocomposites with graphene nanosheets exhibited a different behavior with each mixing method. Nanocomposites prepared by the solution method showed a higher Young's Modulus than those prepared by melt mixing. Results of transmission electronic microscopy and field emission scanning electronic microscopy indicated homogeneous dispersion for carbon nanotubes in melt mixing. Graphene nanocomposites showed some agglomerates, with smaller platelets in the nanocomposites prepared by solution mixing compared to that prepared by the melt mixing.

In this work, nanocomposites with simultaneous dispersion of carbon nanotubes and clays in a high density polyethylene (HDPE) matrix were prepared. Two different processes of preparation were employed: solution or melt intercalation. Two different montmorillonite clays were used separately: a natural (MMT-Na) or an organoclay (MMT-30B) and it was used multiwalled carbon nanotubes (MWCNT). Thermal properties were evaluated by DSC and TGA, mechanical properties were evaluated by nanoindentetion and morphology was investigated by transmission electronic microscopy (TEM). Alterations of 20% in crystallinity were detected, increases in Young´s modulus up to 12% were observed and up to 20% of increase was observed in Oliver-Pharr hardness. It is possible to explain part of those results based on the state of dispersion observed in our TEM results.

In this paper, the influence of calcium carbonate and slip agent on linear medium density polyethylene (LMDPE) processed by rotational molding was evaluated. LMDPE was dry blended with different CaCO3 masterbatch ratios, erucamide slip agent and then extruded, micronized and rotomolded. The powder samples were characterized using MFI (Melting flow index), dry flow and bulk density. The characterization of rotomolded samples properties was performed by DSC (Differential scanning calorimetry), microscopy analysis, izod impact and tensile test. The results pointed out that the CaCO3 addition modifies the bulk density compared to neat LMDPE, but did not significantly affect the dry flow and MFI. The erucamide addition decreased the dry flow and increased the bulk densities. The porosity degree data showed that CaCO3 addition in the LMDPE increased the quantity of pores. The DSC results showed no significant difference in the crystallinity degree. The behavior of porosity led to a decrease in the mechanical properties of LMDPE with the CaCO3 addition.

Nanocomposites based on epoxy and a mixture of clays and multi-walled carbon nanotubes (MWCNT) were produced by casting, and also molded by RTM using glass fibers as reinforcement, yielding a hybrid multi-scale micro/nanocomposite material. Two types of montmorillonite clays were used, natural (MMT-Na) and organophilic (MMT-30B). Higher viscosity was obtained for the mixture with MMT-30B and it was observed that this clay did not perform as well as the MMT-Na in helping the dispersion of the carbon nanotubes (CNT). The glass transition temperature (Tg) of the nanocomposites increased in up to 6 °C with the addition of MWCNT and up to 10 °C with the addition of MMT-30B, differently from the MMT-Na which did not alter the Tg of the material. By transmission electron microscopy, it was verified that more homogeneous dispersions and more intercalated structures were obtained with the MMT-30B than with the MMT-Na. Finally, the low clay content used and, especially, the very low MWCNT content, did not significantly alter the studied flexural properties.

There is a high content of calcium carbonate in mussel and oyster shells, which can be used in the formulation of medicine, in construction or as filler in polymer materials. This work has as its main objective to obtain calcium carbonate from mussel and oyster shells and used as filler in polypropylene compared their properties with polypropylene and commercial calcium carbonate composites. The shellfish was milling and heated at 500 ºC for 2 hours. The powder obtained from shellfish were characterized by scanning electron microscopy (SEM), X-ray fluorescence, particle size distribution and abrasiveness and compared with commercial CaCO3 and mixed with polypropylene. The thermal and mechanical properties of polypropylene with CaCO3 obtained from oyster and mussel shells and with commercial CaCO3 were analysed. The results showed that CaCO3 can be obtained from oyster and mussel shell and is technically possible to replace the commercial CaCO3 for that obtained from the shells of shellfish in polypropylene composites.

Um dos grandes problemas da atualidade é o destino final adequado dos materiais, que não podem ser reutilizados no processo de origem. Dentre os resíduos estão as espumas rígidas de poliuretanos (PUR), que são materiais com ampla aplicação, mas apresentam dificuldades de reaproveitamento tecnológico por serem materiais termorrígidos. O objetivo deste trabalho é aplicar o processo de reciclagem química por glicólise e utilizar o poliol reciclado, produto da reação de glicólise, como parte da matéria prima para formação de espumas rígidas de poliuretano e analisar suas propriedades físicas, mecânicas e térmicas. A formação das células da espuma com poliol reciclado foi avaliada por microscopia eletrônica de varredura (MEV). Os resultados mostram que, nas condições estudadas, não há perdas das propriedades mecânicas e térmicas da espuma de PUR com a utilização de poliol reciclado, satisfazendo as necessidades para aplicação na produção de refrigeradores domésticos.

One of the major problems is the appropriate final destination of the materials or waste that can not be reused in the original process. Among the residues are rigid polyurethane foams, which are widely applied but difficult to reuse because they are thermosetting materials. The aim of this paper is to apply a chemical recycling process, glycolysis, and use the recycled polyol, product of glycolysis reaction, as part of the raw material for the formation of rigid polyurethane foams. Their mechanical properties and thermal conductivity were analyzed. The formation of foam cells with recycled polyol were evaluated by scanning electron microscopy (MEV). The results show that there is no loss of mechanical and thermal properties of PUR foam, satisfying the requirements for the production of domestic refrigerators.

Neste trabalho foi analisada a influência da sequência de mistura do compósito de polipropileno (PP) com 10% em volume de fibras de bananeira (FB) utilizando polipropileno enxertado com anidrido maleico (PP-MA) como agente de acoplamento. As propriedades térmicas, mecânicas, absorção de água e morfologia dos compósitos foram caracterizadas. Foram utilizadas 3 sequências de mistura: o processamento de todos os componentes juntos (PP + PP-MA + FB); a extrusão do PP/PP-MA e após moagem, esta mistura foi processada com a FB ((PP + PP-MA) + FB); e a mistura do PP-MA com a FB seguida da extrusão deste compósito com o PP (PP + (PP-MA + FB)). Os compósitos apresentaram maior estabilidade térmica e menor grau de cristalinidade que o PP puro, independentemente da sequência de mistura. Constatou-se que a mistura de PP + PP-MA + FB processada uma única vez apresentou maior resistência ao impacto. Os compósitos modificados com PP-MA, independentemente da sequência de mistura, apresentaram módulo de elasticidade maior e menor absorção de água que o compósito sem agente de acoplamento. Para a resistência à tração máxima e módulo de elasticidade não ocorreram alterações significativas em relação aos métodos de mistura. Na microscopia eletrônica de varredura foi possível observar que as FB apresentaram maior adesão nos compósitos com PP-MA, principalmente para a composição PP + (PP-MA + FB).

This work analyzed the influence from the sequence of mixture for the composite of polypropylene (PP) with 10% by volume of banana fiber (FB) using maleic anhydride grafted polypropylene (PP-MA) as the coupling agent. The thermal, mechanical, water absorption and morphology of the composites were characterized. Three different sequences were used to mix: the processing of all components together (PP + PP-MA + FB), extrusion of PP / PP-MA and after grinding, the mixture was processed with FB ((PP / PP - MA) + FB), and the mixture of PP-MA with FB followed by extrusion of the composite with PP (PP + (PP-MA + FB)). The composites showed higher thermal stability and lower percent crystallinity than the pure PP, regardless of the sequence of mixing. It was found that the mixture of PP + PP-MA + FB processed once had a higher impact resistance. The composites modified with PP-MA, regardless of the sequence of mixture used, showed higher modulus and lower water absorption than the composite without coupling agent. For the tensile strength and modulus of elasticity no significant changes were observed. The images from scanning electron microscopy indicated that FB had higher adhesion for the composites with PP-MA, especially for composition PP + (PP-MA + FB).

Neste trabalho foi estudada a reação entre polietileno glicol (PEG) e uma resina epoxídica à base de diglicidil éter de bisfenol A (DGEBA), na presença de N,N-dimetilbenzilamina (DMBA), sendo os produtos desta reação avaliados por espectroscopia no infravermelho (FTIR), espectroscopia de ressonância magnética nuclear de próton (RMN-1H) e medidas de viscosidade cone-prato. Amostras curadas com um endurecedor à base de poliamina foram também submetidas a ensaios de tração e calorimetria exploratória diferencial (DSC). Os resultados das análises de viscosidade, FTIR e RMN (1H) confirmaram a ocorrência da reação entre grupos epóxi do DGEBA e grupos hidroxila do PEG na presença de DMBA, a 100 ºC. As análises de DSC e os ensaios de tração dos sistemas curados mostram que a reação de DGEBA com PEG gera um material com temperatura de transição vítrea (Tg) significativamente menor, em conjunto com o aumento da deformação na ruptura e decréscimo do modulo de elasticidade, quando comparados ao sistema epoxídico de referência (DGEBA).

In this work the reaction of polyethylene glycol (PEG) and epoxy resin (BADGE) in the presence of N,N-dimethylbenzylamine (DMBA) was studied. The reaction products were evaluated by infrared spectroscopy (FTIR), nuclear magnetic resonance spectroscopy (NMR) and viscosity measurements. Samples cured with a polyamine-based hardener were also submitted to tensile tests and differential scanning calorimetry (DSC). The results of the viscosity analyses, FTIR and RMN (¹H) confirmed the reaction between DGEBA epoxy groups and PEG hydroxyl groups in the presence of DMBA, at 100 ºC. DSC analyses and tensile tests of cured systems showed that the reaction of DGEBA with PEG leads to a reduction of Tg, generating a more flexible material.